On the blog: The finished Sunshine Coat, complete with lining!

So…drum roll please, here is the finished Sunshine Coat in all its glory!

SunshineCoat8SunshineCoat7 SunshineCoat9

 

 

 

 

 

 

 

Delivery took place on Sunday, and as you can see, my friend’s happiness matches the cheery combination of yellow and soft lavender!  It fits beautifully too – although I should remind you/note that the size modelled is one smaller than my friend would normally wear.  The coat has a very generous fit, so if you have plans to make it and would prefer a more fitted look, I would recommend going a size smaller than your usual.  But do check the finished dimensions on the spec drawing and measure yourself – we did, to be absolutely sure.

The last thing I’ll share is how I constructed and inserted the lining.  Pattern cutting isn’t my specialism, so if you know better, or know somebody who knows better, then do ask them for tips if you’d like to try lining handknits.  I recommend it for coats like this because it gives the garment more structure, durability and strength; because the lining takes the weight of the coat and is in a woven fabric, there’ll be the option of storing the coat on a hanger as well as keeping it folded in a drawer.  And the hanger is probably the better option too.

To make the lining: You will need a long ruler (a metre long if possible); dot and cross paper (you can get this from most good haberdashery stores), scissors, pencil and a pattern master/French curves.  We purchased 2 metres of lining fabric, 150cm wide.

Before doing anything else, make sure you block or press the finished pieces of the knitting to size – this is VERY important.  If they don’t lie straight, you will end up with wonky pattern pieces.  Woven fabrics are far more rigid and unforgiving than knitted fabrics, so they must be cut accurately.

1) Using your garment pieces as a template, carefully trace around each one onto the dot and cross paper, making sure that the vertical line of each is lined up with the grid-like pattern that the dots and crosses make.

SunshineCoatLining6 SunshineCoatLining72) When you have traced around each piece, neaten the lines with your ruler to create smooth edges – this may take some work and making a line of best fit!  If there are curved lines (see sleeve cap opposite), e.g. around the neck or at the top of the sleeve, use your pattern master or French curves to help you.

3) To create the back lining piece, fold this knitted piece in half and add about 2-3 cm in width to create a pleat at the centre back (see below):

SunshineCoat_BackLiningSketch4) When the edges are smooth, extend the length of each traced piece by about 4cm so that you can create a hem later.

5) Now add a 1.5cm seam allowance to each pattern piece, around the entire edge, EXCEPT for the back.  The back will be cut on the fold, so do not add seam allowance to the centre, i.e. where you’ve added extra for the pleat.  Instead, mark the beginning of the pleat extension so that you have a guide when preparing your fabric.

6) When seam allowances have been added, place a grainline (see above) on all pieces that will not be cut on the fold.  Because you’ve already vertically aligned your tracing, you can use the dots and crosses to draw a perpendicular straight line.

7) Now that the pieces are prepared and look vaguely like shop-bought dress patterns, you’re ready to cut them out, ready for the fabric.  Here’s how mine looked, laid out on the fabric but before pinning and cutting:

SunshineCoatLining8* When cutting out the back, make sure that you mark the centre, i.e. the fold, and the beginning of the pleat.

8) I overlocked (serged) my edges immediately after cutting out, but if you don’t have an overlocker (serger), don’t worry, you can finish the edges as you go with good old zigzag stitch, a double line of stitching…it is up to you.

9) After cutting out, I created an inverted box pleat at the centre back (see diagram below).  Reinforce the pleat by making some ‘on the spot’ running stitches between the two pieces.

SunshineCoat_InvBoxPleatSketch10) Next, machine stitch the pieces together.  I did the raglans first, then the side and sleeve seams; this enabled me to sew in one continuous line from hem edge to sleeve edge.

11) Press seams open and insert lining into coat to check the fit (if you have a dress form, it could be helpful here.  Secure with pins at the armholes and at the top of the raglan seams.  Then try on the coat, being mindful of the pins!

SunshineCoatLining212) Mark the position for the hem as best you can (try to get someone to help you if you are wearing the coat whilst fitting; if not, work flat and measure up from the bottom edge).  It should be folded over twice for the body and sleeves, and finish about 3cm up from the finished edges of the coat.  Trim fabric if you need to.  The main thing is that the lining doesn’t peek out at the bottom and look untidy.

13) After creating the hem, press to finish; then press over the 1.5cm seam allowance at the front edges, sleeve tops and back neck.

14) Now to insert the lining proper – nearly there!  To do this I secured the lining at the armholes and the top of the raglan seams with some on the spot stitches, the lining sleeve hem to the edge of the sleeve seam (approx 3cm from edge as in point 12) then oversewed the pressed edges around the inside perimeter of the coat.  Ease in any fullness at the back neck; let the skirt of the lining hang free.

15) That’s it!  That’s how I lined the coat.    We are THRILLED with the results 🙂

SunshineCoat9 SunshineCoat7This was a great challenge for me; it got some rusty cogs turning in my brain as I very rarely bother with any kind of pattern cutting, but I’m glad it all worked out well.  If you are a knitter with sewing skills, I recommend doing this for heavy outerwear garments – or even if you fancy stretching yourself a bit.  The one detail I could’ve included to be more professional was  to add balance markers to the pattern pieces, but in the end I just used my eyes and trusted myself to measure and cut accurately (read: got slightly lazy at the final hurdle).  Luckily – happily – it worked out in the end, and my friend finally has her bespoke coat after waiting so patiently.  🙂

 

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s